LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 1 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 1 form a solid-state relay description the LH1546AEF (4 pin sop) is robust, ideal for telecom and ground fault applications. it is an spst normally open switch (1 form a) that replaces electromechanical relays in many applications. it is constructed using a gaas led for actuation control and mosfets for the switch output. in addition, it employs current- limiting circuitry which meets lightning surge testing as per ansi/tia-968-b and other regulatory voltage surge requirements when overvoltage protection is provided. features ? current limit protection ? isolation test voltage 3750 v rms ? typical r on 28 ? load voltage 350 v ? load current 120 ma ? high surge capability ? clean bounce free switching ? low power consumption ? smd lead availabl e on tape and reel ? equivalent to cpc1035n ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ? general telecom switching - on/off hook control - ring relay - dial pulse - ground start - ground fault protection ? instrumentation ? industrial controls note ? see solid-state rela ys (application note 56) agency approvals ? ul1577, file no. e52744 system code o ? bsi/babt certification no. 8500 issue 2 18221-1 1 2 a k 4 3 s s 1 ss ' 22624 ordering information lh1546a##t# part number electr. variation package config. tape and reel package ul, bsi sop-4, tape and reel (t2 rotation) LH1546AEFt2 sop-4, tape and reel LH1546AEFtr sop-4, tubes LH1546AEF s op-# 7.21 mm
LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 2 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mounted devices. note ? minimum and maximum values are testing requirements. typical valu es are characteristics of the device and are the result of en gineering evaluations. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input led continuous forward current i f 50 ma led reverse voltage i r 10 a v r 6v output dc or peak ac load voltage i l 50 a v l 350 v continuous dc load current at 25 c, bidirectional i l 120 ma ssr ssr output power dissipation (continuous) p diss 550 mw ambient temperature range t amb - 40 to + 85 c storage temperature range t stg - 40 to + 150 c soldering temperature (1) t = 10 s max. t sld 260 c isolation test voltage t = 1 min v iso 3750 v rms isolation resistance v io = 500 v, t amb = 25 c r io 10 12 v io = 500 v, t amb = 100 c r io 10 11 electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input led forward current, switch turn-on i l = 100 ma, t = 10 ms i fon 1.1 2 ma led forward current, switch turn-off v l = 300 v i foff 0.2 0.6 ma led forward voltage i f = 10 ma v f 1 1.18 1.45 v output on-resistance, ac/dc: pin 3 () to 4 () i f = 5 ma, i l = 50 ma r on 28 35 off-resistance i f = 0 ma, v l = 100 v r off 0.5 5000 g off-state leakage current i f = 0 ma, v l = 100 v i o 0.32 200 na i f = 0 ma, v l = 350 v i o 1na output capacitance pin 3 to 4 i f = 0 ma, v l = 1 v c o 55 pf i f = 0 ma, v l = 50 v c o 10 pf current limit i f = 5 ma, t = 5 ms, v l = 6 v i limit 170 210 250 ma transfer capacitance (input to output) v iso = 1 v c io 0.6 pf switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit turn-on time i f = 5 ma, i l = 50 ma t on 23ms turn-off time i f = 5 ma, i l = 50 ma t off 0.08 3 ms
LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 3 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - led voltage vs. temperature fig. 2 - led current for sw itch turn-on vs. temperature fig. 3 - on-resistance vs. temperature fig. 4 - switch breakdown voltage vs. temperature fig. 5 - switch capacitance vs. applied voltage fig. 6 - leakage current vs. applied voltage iLH1546AEF_01 t a - ambient temperature (c) led forward voltage (v) - 40 - 20 0 20 40 60 80 1.6 1.5 1.4 1.3 1.2 1.1 1.0 i f = 2 ma i f = 5 ma i f = 10 ma i f = 50 ma i f = 20 ma i f = 1 ma iLH1546AEF_02 ambient temperature (c) 100 - 60 80 60 40 - 40 - 40 20 - 20 0 - 20 0 20 40 60 80 i l = 100 ma led forward current for switch turn-on (%), normalized to 25 c iLH1546AEF_03 - 40 0 10 20 30 40 - 10 - 40 - 20 - 30 - 20 0 20 40 60 ambient temperature (c) 80 i f = 5.0 ma i l = 50 ma change in r on (%) iLH1546AEF_05 - 40 - 20 0 20 40 60 80 ambient temperature (c) 8 0 4 2 6 - 2 - 6 - 8 - 4 change in breakdown voltage (%) normalized to 25 c iLH1546AEF_06 02040 applied voltage (v) 80 50 70 60 40 20 0 10 60 30 100 80 capacitance (pf) iLH1546AEF_07 0 50 100 load voltage (v) 150 200 250 300 350 400 0.1 1 10 100 leakage (pa) t = 85 c t = 70 c t = 50 c t = 25 c
LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 4 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 7 - leakage current vs. applied voltage fig. 8 - turn-off time vs. temperature fig. 9 - turn-on time vs. led current iLH1546AEF_08 0 50 100 load voltage (v) 150 200 250 300 350 400 1 10 100 1000 10 000 leakage (pa) iLH1546AEF_09 - 80 - 60 - 40 - 20 0 20 40 60 80 change in t off (%) normalized to 25 c - 40 - 20 0 20 40 60 ambient temperature (c) 80 i f = 10 ma i f = 5.0 ma i f = 4.0 ma i f = 3.0 ma i f = 2.0 ma i f = 6.0 ma i f = 8.0 ma iLH1546AEF_10 0 1 2 3 4 5 6 7 t on (ms) 0 5 10 15 20 25 30 35 40 45 led forward current (ma) 50 t = 85 c t = 25 c t = - 40 c
LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 5 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example) note ? tape and reel suffix (tr) is not part of the package marking. 22625-1 5.59 5.09 0.80 5.6413 min. 5.8953 typ. 6 0.05 max. lead s co-planarity 0.100 max. 0.204 0.63 0.37 7.21 6.71 s ide view 5.7861 min. 6.0401 typ. 5.0800 min. 5.5880 typ. 4.67 4.17 0.84 0.78 2.33 1.91 0.46 0.36 2.59 2.49 0.00 0.10 10 front view 4.83 4.33 4.67 4.17 top view pin 1 i.d. 5.3594 min. 5.6134 typ. matte s older fini s h lead s lh1546 v yww o 68
LH1546AEF, LH1546AEFtr www.vishay.com vishay semiconductors rev. 1.9, 16-aug-12 6 document number: 83837 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tape anr reel dimensions in millimeters fig. 10 - LH1546AEFtr, 2000 per reel fig. 11 - LH1546AEFt2, t2 rotation, 2000 per reel 8 0.76r 4 typ. 4.30 0.318 + 0.3 - 0.1 2.36 0.1 2.66 0.1 7.33 0.1 12.00 2.00 0.05 1 2 3 4 4.00 0.1 1.50 + 0.1 1.75 0.1 8.00 0.1 4.72 0.1 1.50 0.25 5.50 0.05 + 0.3 - 0.1 21598 2.0 0.05 (0.079 0.002) 4.0 0.1 (0.157 0.004) 1.50 + 0.1/- 0.0 (0.059 + 0.004/- 0.0) 1.75 0.1 (0.069 0.004) 5.5 0.05 (0.216 0.002) 12.0 + 0.3/- 0.1 (0.472 + 0.012/- 0.004) 7.33 0.1 (0.289 0.004) 12.0 0.1 (0.472 0.004) 1.50 + 0.25/- 0.0 (0.059 + 0.010/- 0.0) 4.72 0.1 (0.186 0.004) 2.66 0.1 (0.105 0.004) 2.36 0.1 (0.093 0.004) 0.320 0.03 (0.0125 0.0012) typ. 4.30 section x - x section y - y x x r 0.3 typical c l 4 c l 8 y 1 2 4 3
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
